DOCK LEVELLERS WITH TELESCOPIC LIP
Dock leveller with a telescopic lip or extension
CUSTOMISATION
We custom manufacture dock levellers perfectly adapted to your specific needs in terms of dimensions and load capacity.
Dock levellers » Hydraulic dock leveller with telescopic lip
We custom manufacture dock levellers perfectly adapted to your specific needs in terms of dimensions and load capacity.
Hydraulic dock leveller with telescopic lip.
The front of the leveller platform features a 1‑metre telescopic lip that extends beyond the leveller when activated in order to bridge the gap to the vehicle’s bed.
This design means the sectional door can be fully closed in front of the dock leveller, thus providing unbeatable thermal and hygienic insulation.
We use different materiales, en función del riesgo de corrosión: especifically, stainless, galvanised and painted steel, plus combinations thereof.
TI – STAINLESS STEEL
GI – STAINLESS AND GALVANISED STEEL
AP – PAINTED STEEL
Each component in our dock levellers is manufactured using different materials depending on the risk of corrosion: namely, stainless, galvanised and painted steel and combinations thereof.
Models | MSRHR-AP | MSRHR-PG | MSRHR-TG | MSRHR-GI | MSRHR-TI |
---|---|---|---|---|---|
Top plate | Painted steel | Galvanised steel | Galvanised steel | Stainless steel | Stainless steel |
Front lip | Galvanised steel | ||||
Side panels | Stainless steel | ||||
Frame and base structure | Painted steel | Galvanised steel | |||
Cylinders | Painted steel | ||||
Couplings | Zinc-plated steel |
Thanks to our ample range of products, we can always find the best solution for your needs.
Model | Load capacity (kg) | Width (mm) | Length (mm) | Working dimensions (mm) |
---|---|---|---|---|
MSRHR-20/25 (*) | 6.000 | 2.000 | 2.500 | 3.500 |
MSRHR-20/30 | 3.000 | 4.000 |
(*) Standard model.
These hydraulic dock levellers are intended for installation in a pit and with a height difference of around 1.20 m between the warehouse floor and exterior.
The MSRHR-20/25, with a 6,000 kg load capacity, is our standard hydraulic dock leveller with telescopic lip.
It is 2,000 mm wide and ideal for loading/unloading trucks and trailers of all shapes and sizes.
The MSRHR-20/25 is 2,500 mm deep, while the telescopic lip adds a further 1.000 mm, giving 3,500 mm in total. Designed to bridge gaps of ±350 mm.
When retracted, our dock levellers are perfectly flush with the warehouse floor, so forklifts can pass across effortlessly.
Galvanised steel adjustable bumpers: Built with durable external steel plates and rubber linings. Adjustable vertically and in the direction of compression. Dimensions: 300 mm x 450 mm x 125 mm.
Reinforced adjustable bumpers: Built with durable external steel plates and rubber linings. Adjustable vertically and in the direction of compression. Dimensions: 300 mm x 450 mm x 125 mm.
Rubber bumpers Rubber profile with an inner steel reinforcement and fastening hardware. Dimensions: 120 mm x 500 mm x 110 mm.
Barriers to ensure vehicles take up the correct position when parking in the loading dock. Embedded in the floor for solid installation. Painted with yellow stripes for high visibility.
CONTROL PANEL STAND
Convenient stand for supporting dock leveller or lifting table control panels.
COJINES DE ESTANQUEIDAD
Cojines aislantes que evitan el paso de aire en la parte inferior de los abrigos. Foam padding with a PVC coating. Supplied with installation supports.
TELESCOPIC BUMPERS
Telescopic bumpers provide increased protection for INDOCK loading system.
GUARDRAILS
DOORSTOPS
Doorstops to prevent the trailer doors closing while loading/unloading the vehicle.
TRAFFIC LIGHTS
BUMPERS IN BARS
Rubber bumpers supported by two bars embedded in the ground to stop trucks from banging against the lifting tables.
Copyright © 2020 MS METALSYSTEM SL. All rights reserved.